Hughes 4510 S-band Terminal

High Efficiency, all-IP terminal for satellite and cellular connectivity

For mobile, land and maritime packet data network applications requiring high-quality coverage across satellite and cellular networks, the Hughes 4510 S-band terminal is an affordable solution that delivers ‘always-on’, hybrid connectivity.

The low standby power consumption of the Hughes 4510 terminal makes it possible to provide ubiquitous IP connectivity to sites that are otherwise off the grid and is well-suited for power challenged locations that rely upon solar-battery arrays with limited power budgets.

Introduction

Dynamically routing IP traffic between terrestrial and satellite networks based upon path availability, the Hughes 4510 S-band terminal provides end-to-end connectivity ideal for a wide range of industrial IOT applications, including connected vehicles, industrial, fisheries, resource extraction, environmental monitoring, and Smart-Grid monitoring.

The Hughes 4510 S-band terminal can be installed with ease, with just a single unit connected to one power and Ethernet cable. It is environmentally sealed for long-term outdoor use on fixed or moving locations, including vehicles and offshore vessels.

4510 S-Band Terminal

Features of the Hughes 4510 S-band Terminal

  • S-band satellite operation with data rates up to 200 kbps forward and 150 kbps return
  • Omnidirectional satellite antenna allowing mobile communications with no moving parts
  • Global LTE CAT-1 operation enabled by either an embedded-SIM (eSIM) or a replaceable 2FF SIM
  • Integrated cellular antenna
  • Integrated connection watchdog to ensure “always-on” network connectivity, with no manual intervention required to recover from an outage
  • Supports remote terminal management and firmware upgrades
  • Auto-on and auto-context activation automatically restores power and connection following any network issues or total loss of power
  • Low power consumption Transmit: < 16 W (SAT only); < 6 W (CELL only); < 20 W (SAT & CELL)
  • Receive: < 10 W
  • Idle (SAT only): < 1.3 W
  • Idle (SAT & CELL): < 3 W
  • Off (Remote switch control): < 10 mW
  • Simple installation: no PC required
  • Terminal can be vehicle-, pole-, or mag-mounted
  • Weatherproof (IP-67) enclosure
  • Built-in GNSS receiver

Interfaces

  • Ethernet connection
  • Nominal 12V power input voltage; power supply must be able to handle 3.5A peak current
  • USB for connection to configuration PC
  • SIM connectors under cover
  • Serial data and GPIO options

Package Contents

  • Hughes 4510 terminal
  • Quick Start Guide

Accessories

  • Connection cables
  • Vehicular-, pole-, or mag-mounting kits
  • Extended warranty option

Technical Specifications

SAT Transmit Freq
1995–2010 MHz
SAT Receive Freq
2185–2200 MHz
LTE bands
1, 2, 3, 4, 5, 7, 8, 12, 18, 19, 20, 28
7-bands UMTS bands
800, 850, 900,1700/2100 (AWS), 1800, 1900 and 2100 MHz (bands 1, 2, 4, 5, 8, 9, 19)
GSM Bands
850, 900, 1800, 1900
Fallback support for
GPRS/EDGE/HSPA+
GNSS Support
GPS
Terminal Weight
1.5kg
Operating Temp
-25 to +65 °C
Storage Temp
-40 to +80 °C
Power: Transmit
< 16 W (SAT only) < 6 W (CELL only) < 20 W (SAT & CELL)
Power: Receive
< 10 W
Power: Idle
< 1.3 W (SAT only) <3 W (SAT & CELL)
Power: Off (Remote Switch Control)
< 10 mW
Input Voltage +12V
(vehicle)